FT-R3050 imagesetter operation panel information display (two)
We are a big printing company in Shenzhen China . We offer all book publications, hardcover book printing, papercover book printing, hardcover notebook, sprial book printing, saddle stiching book printing, booklet printing,packaging box, calendars, all kinds of PVC, product brochures, notes, Children's book, stickers, all kinds of special paper color printing products, game cardand so on.
For more information please visit
http://www.joyful-printing.com. ENG only
http://www.joyful-printing.net
http://www.joyful-printing.org
email: info@joyful-printing.net
Error message
1. Loading error: This error message is usually displayed after the film is sliced or after the film is cut, indicating that there is an error on the machine. If it appears when the film is replaced after the film is replaced, you can try to send the film forward by hand and then execute the film command. It is generally indicated that this error may be damage to the motor, clutch, and possibly loosening of the tightening screw on the motor.
2. FAN trouble 1 and FAN trouble 2: This message indicates that there is a problem with the fans of the imagesetter and generally needs to be replaced. FAN 1 is the lower fan and FAN 2 is the upper fan.
3. Download error 1: This information will only appear when the main version is downloaded. Generally, users are not recommended to do the download work themselves. The operation error will cause the chip on the main board to be damaged.
4. Mode unmatch: This message indicates that the settings on the main board do not match the system data. This error does not generally occur when the user does not privately modify the jumper switch on the main board. When it is found that this error is displayed, it is recommended to contact a professional service person for repair.
5. Flim jam 1 (a) and Flim jam 2 (a): This is the machine display card. Both card information is that the machine's lower sensor does not detect the film. There are many reasons for the two card cases, such as: the next sensor is damaged or the position is wrong, the cutting system has a problem, the main roller or the driving roller has a problem, the main board or the OPTV board has a problem, etc., in the process, one step is needed. One-step inspection is excluded. What needs to be reminded here is that when the card is removed, it is not allowed to use the hard force to pull out. It is necessary to pay attention to where the film is stuck and cannot be pulled out, and then carefully take it out, otherwise it may cause other sensors to be misaligned or some motors. It was burned. Generally, when the two cards are taken out, the machine can be cut first by using the machine cutter (the cutter has no problem), so that the film can be taken out in two stages.
6. Flim jam 3 (a): This card error will only occur on the machine that uses the clip. It may be a problem with the clip connection, or there are any remaining clips in the clip, or the sensor is damaged or in poor position. Or the main version is damaged, you can check it first from the film holder.
7. Flim jam 10 (a): This card error will only occur on machines with a line-up processor. The solution is the same as for Flim jam 1 (a) and Flim jam 2 (a).
8. Flim jam 11 (a): This card phenomenon only exists on the machine of the tandem film processor. When the film is sent to the film processor, the film sensor of the 65-second camera also detects the film. Exist, the machine will report this error.
9. Flim jam 12 (a): This message will only appear on the machine of the connected line puncher. When the rear lower motor starts to rotate, after 8 seconds, the punch sensor is still not open. The machine will get this error message. When this error message appears, the user should check whether the ground wire of the two machines is normal, clear the fee film in the sub-collection clip, and then re-set the sub-collection clip.
10. Flim jam 13 (a): This information will only appear on the machine of the tandem film processor. When the cut film is sent to the film processor, the next film sensor of the phototype machine has been 180 minutes later. Off (no film), the chip sensor is still on. Generally, when this error message occurs, there is a problem with the parameter adjustment of the film processor, and it is necessary to check the correction.
11. Flim jam 14 (a): This error message appears during the process of the film being cut into the film processor. The chip sensor is still off within 2 seconds of the AT door opening. After this message appears, the user can check whether the imagesetter and the puncher are docked and the position is appropriate. If the problem persists after reconnecting, check if the operation of the AT door is normal. The motor may be broken or the connection between the motor and the door may be loose.
12. Flim jam 2 (d) and Flim jam 2 (b): These two error messages only appear on machines that use the capture mode. It will appear in the following cases: the film holder is not placed, the rear buffered guide roller is not placed, and the sensor of the rear buffer guide roller is displaced or damaged, and the motherboard has a problem.
13. Machine error 3: This message indicates a problem with the cutting system, which may be a problem with the cutter system or the motherboard.
14. Machine error 5: This message indicates that the backboard has problems during the shutdown process. In the event of such an error, the sensor of the rear baffle should be checked, the motor of the rear baffle, the fuse and the main board.
15. Machine error 6: This message indicates that there is a problem when the front bezel is closed. The sensor of the front bezel should be checked, the motor of the front bezel, the fuse and the main board should be controlled.
16. Machine error 7: A malfunction occurs when the pinch roller is raised and the machine displays this error message. Generally, the pinch roller position sensor is damaged or the position is not good, the pinch roller motor is damaged, the connecting screw between the pinch roller motor and the roller is loose, and there is a problem in the insurance or the main board.
17. Machine error 9: This error message appears when there is a problem with the filter inside the machine. Check the position sensor of the filter, the fuse, the motor, and the motherboard.
18. Machine error 11: This message indicates that when the AT door is closed, it is necessary to check the sensor, motor, fuse, and motherboard of the AT gate.
19. Machine error 12 and Machine error 15: These two messages indicate that the exposure failed. Generally, it is necessary to check whether the light intensity detecting sensor is dirty, whether the voltage on the OPTV version is too low, and whether the laser is damaged.
20. Machine error 16: This error message indicates a problem with the camera mirror. Generally, it should be checked whether the mirror is not installed, damaged, whether the drive motor of the mirror is damaged, whether there is a problem with the motherboard and the power supply.
twenty one. Data write error: This message shows a problem when writing system data. This information generally appears when modifying system data or display language. This information needs to be contacted by the manufacturer to replace the EPROM.
twenty two. Film jam 2 (c): This card information appears on the machine using the folder mode. In the A mode, the error message will appear when the film has not yet been buffered for 10 seconds after the film is cut. At this time, check whether the paper clip is installed, whether the rear buffer roller is installed, whether there are any remaining sheets in the paper clip, and whether the rear buffer sensor is damaged or not.
twenty three. Film jam 2 (e): This message indicates that the film is jammed in the folder position. You need to check if the clip is installed, whether the clip sensor is damaged or not.
twenty four. Machine error 19: This message indicates that the machine has problems during the opening of the rear panel. In the event of such an error, the sensor of the rear baffle should be checked, the motor of the rear baffle, the fuse and the main board.
25. Machine error 20: This message indicates that there is a problem when the front bezel is open. The sensor of the front bezel should be checked, the motor of the front bezel, the fuse and the main board should be controlled.
26. Machine error 21: A malfunction occurs when the pinch roller falls, and the machine displays this error message. Generally, the pinch roller position sensor is damaged or the position is not good, the pinch roller motor is damaged, the connecting screw between the pinch roller motor and the roller is loose, and there is a problem in the insurance or the main board.
27. Machine error 23: This message indicates that when the AT door is open, it is necessary to check the sensor, motor, fuse, and motherboard of the AT gate.
28. Machine error 24: This message appears when there is a problem with the front bezel, which is usually damaged by the sensor or a problem with the motherboard.
29. Machine error 25: This information is also related to the front panel. The sensor and motherboard of the front panel should be checked.
30. Machine error 26: This information will only appear on the machine equipped with the punching device, prompting the user to malfunction. The sensor should check the position of the sensor and whether it is damaged. The motor of the punching device works normally. , insurance and motherboard damage.
31. Machine error 27: This information will only appear on the machine equipped with the punching device, prompting the user that the sensor of the punching device has a working condition, and the items to be inspected are the same as above.
32. I/F error 1: This error message indicates that SCSI has a problem during data transmission and you need to restart the machine.
33. Serial error: This message indicates a problem with the data transfer inside the machine. Check the SCON board and the connections on it.
34. Setting error 1: The position of the jumper on the SCON board is incorrect and needs to be corrected.
35. Setting error 2: This message indicates that a payroll connection on the SCON board is incorrect.
36. Image error: This information usually appears during the exposure process. If the error message appears frequently on the machine, it indicates that the hard disk of the photo machine needs to be replaced. When the machine is working without a hard disk, this information is also caused. Because the file transfer speed is different from the exposure speed of the imagesetter, it is recommended that users do not use the state without a hard disk.
37. Disk 1 crash and Disk 2 crash, Disk 1 error and Disk 2 error, Disk 1 Re-format and Disk 2 Re-format, Disk 1 Bus error and Disk 2 Bus error, Disk 1 Unmounted and Disk 2 Unmounted: These messages are Prompt that there is a problem with the hard disk inside the machine. The screen FT-R3050 has two hard disks in the machine. This information indicates which user has a problem with the hard disk. When this information appears, the user should check whether the connection of the hard disk is connected, initialize the hard disk, and check whether the control circuit board of the hard disk is damaged.