Iron first and then print the "unique secret", come and see!
With the great improvement of people's living standards and the improvement of aesthetic concepts, the packaging and printing process has gradually developed to exquisite and high-end, and paper printing such as laser paper, holographic positioning paper, and transfer laser film paper with special light sensing effects has risen significantly, which has greatly enriched the packaging printing process. However, with the increasingly strict national environmental protection requirements and the improvement of people's awareness of environmental protection, the use of hot stamping to highlight the main elements and patterns of packaging design has become the preferred printing process to replace laser paper, holographic positioning paper and other aluminum paper containing heavy metals.
Hot stamping is divided into cold hot stamping and hot stamping. Hot stamping has the advantages of good stability, saving the use of electrochemical aluminum, good adhesion effect of the printing pattern on the hot stamping, easy control of the printing level transfer effect, and high product yield, so it is the use of more hot stamping processes.
The electrochemical aluminum used in the hot stamping has plain surface electroconciliated aluminum, laser electrochemical aluminum and laser column electrochemical aluminum, etc., among which laser electrochemical aluminum has the advantages of high brightness, good light effect and dazzling effect, etc., which has become the most used electrochemical aluminum in process design, because offset printing has the advantages of realistic color gradation reproduction, rich layering, delicate printing pattern, clear dot restoration, etc., becoming the most used printing method.
Precautions for the hot stamping process
When hot stamping, it is not only necessary to ensure the effect of hot stamping, but also to consider whether it meets the requirements of printing suitability, so the following aspects should be paid attention to when hot stamping.
01
The firmness of hot stamping aluminum foil
When hot stamping, the hot stamped aluminum foil layer is required to be firmly attached to the surface of the paper. Otherwise, the aluminum foil layer is easily pulled down by the ink and adheres to the rubber sheet during the offset printing process, causing quality problems such as hot stamping aluminum foil falling off, loss of dots, and defective graphics. To ensure that the hot stamping aluminum foil is firmly attached, pay attention to the following aspects.
(1) Choose the appropriate electrochemical aluminum according to different paper characteristics. The commonly used paper in packaging printing includes white cardboard, glass cardboard, copper plate paper, glass copper plate paper, laser transfer paper, laser laminated paper, etc., and the coating material, adsorption and surface tension of the paper surface are very different, and electrochemical aluminum is mainly adhered to the paper through the adhesive layer, because there are many types of thermoplastic resins, and the characteristics are also different, so different types of paper must choose electrochemical aluminum that matches the viscose layer.
(2) In the process of hot stamping, the temperature, pressure and speed should be controlled, especially pay attention to the treatment of the pressure during hot stamping, the pressure should not be too large, the pressure during hot stamping will cause the surface of the paper to dent, resulting in the appearance of incomplete graphics and text during printing, and at the same time, it is also necessary to standardize the operation of the machine personnel, and check the adhesion firmness of the hot stamping aluminum foil regularly.
The specific operation is: first, stick the adhesive tape flatly on the hot stamping pattern, require the adhesive tape not to foam and not wrinkle, and then quickly pull off the viscose tape glued to the hot stamping pattern to see if the hot stamping aluminum foil is pulled off. otherwise, it means that the hot stamping aluminum foil is not firmly attached and the pressure needs to be adjusted again.
(3) It is easy to have the problem of insufficient attachment of hot stamping aluminum foil when performing large-area hot stamping, mainly due to insufficient exhaust between the hot stamping plate, electrochemical aluminum and paper when pressing large area hot stamping. In this case, the hot stamping plate can be engraved in the middle of the high middle and the edge is low, usually the height difference between the middle and the edge of the hot stamping plate for a large area is about 0.01mm. In addition, the drum type circular hot stamping method can better solve the problem of insufficient hot stamping in large areas, because round stamping is a line contact pressure, which can effectively solve the problem of insufficient hot stamping aluminum foil caused by insufficient contact pressure exhaust on the flat pressing and flat stamping surface.
02
The surface tension of hot stamping aluminum foil
After hot stamping, the surface tension dyne value of hot stamping aluminum foil should be greater than 38, and usually the surface tension dyne value of hot stamping aluminum foil can reach 40, which can be detected with a dyne pen. If the dyne value is lower than 38, the adhesion effect of the ink on the hot stamping aluminum foil after printing is poor, and it will be easily rubbed off, which means that the quality of electrochemical aluminum is unqualified and needs to be replaced.
03
The brightness of hot stamping aluminum foil
The varying brightness of electrochemical aluminum foil can also affect the hue after printing. The brightness of electrochemical aluminum foil is high, the color after printing is more vivid, and the dazzling light effect is better; On the contrary, the aluminum foil after hot stamping is darker, the color vividness after printing decreases, and the dazzling light effect is poor. In addition, it should be noted that the temperature should not be too high during hot stamping, otherwise, it is easy to reduce the brightness of the aluminum foil after hot stamping and affect the color of the pattern.
Precautions for the offset printing process
Due to the large difference between the ink absorption, adhesion, and drying effect of the aluminum foil on the surface of the substrate and the surface of the paper, the following points should be paid attention to when offset printing after hot stamping.
(1) The amount of ink used for offset printing after hot stamping is large, usually the ink consumption of glass cardboard and copper plate paper is about 150%~200%, which is 1.3~1.5 times that of laser paper. When printing with large ink volume and high saturation, it is necessary to add an appropriate amount of ink mixing oil to improve the fluidity of the ink, otherwise there will be a large amount of ink on the ink road, and there will be a sound of "beep beep" ink thread pulling during printing, and the color after printing is lighter and the saturation is poor. The addition ratio of ink blending oil is usually 2%~6%.
When adding ink mixing oil, the amount of ink mixing oil should be determined according to the ambient temperature. When the ambient temperature is high, the fluidity of the ink is better, which can reduce the addition ratio; On the other hand, when the ambient temperature is low, the addition ratio needs to be increased. When the ambient temperature is lower than 15°C, the fluidity of the ink will be significantly reduced, and the ink transfer effect and uniform effect on the ink path will be greatly reduced. When the ambient temperature is too low, the addition ratio of ink mixing oil can be appropriately increased to about 8%, but it should be noted that when the proportion of ink mixing oil is too large, the problem of floating dirt on the page will occur, which can be solved by using ink with high water resistance. At the same time, when printing in a low temperature environment, the ink transfer capacity can also be increased by increasing the temperature of the ink string roller, and the temperature can be increased to about 33°C.
(2) In addition, when printing large ink volume and high saturation field, you should also pay attention to the leveling effect of the printing pattern ink. When the amount of ink is large, the printing pattern is prone to the phenomenon of "pockmarks", which seriously affects the printing effect, at this time, it can be solved by reducing the ink viscosity, using soft blanket liner paper, increasing the method of imprinting unit, or using ink with a higher color concentration to reduce the amount of ink used, improve the ink transfer effect, and make the ink color after printing flat and no pockmarks.
(3) The hot stamping foil is pulled back during offset printing is the most likely problem. When the adhesion firmness of hot stamping aluminum foil is slightly poor, the method of adding viscosity reducer to the ink and reducing the printing speed can be used to reduce the tension backlash problem. If the adhesion firmness of the hot stamping aluminum foil is poor and cannot be offset printed, you can use the hot stamping method to hot press the hot stamping products with infirm attachment to the aluminum foil before printing, and the temperature should not be too high when hot pressing, usually at 50 °C ~ 60 °C, and the hot stamping pressure needs to be treated but no need to use electrochemical aluminum.
(4) When offset printing after hot stamping, you also need to pay attention to the adhesion effect of the ink, usually UV ink drying has "surface dry" and "inner dry", the newly printed ink is cured after UV lamp irradiation, the curing at this time is "surface dry", the "inner dry" at the connection between the ink layer and the substrate has not been completely cured, and needs to be left for more than 4 hours, when the "surface dry" and "inner dry" are completely cured, and the adhesion effect of the ink will be fully reflected. In addition, in order to make the offset ink firmly adhere to the surface of the hot stamping aluminum foil, a UV varnish can also be used to cover the printing surface after offset printing.
Of course, to do a good job in the process of ironing and then printing, it is necessary to select paper, electrochemical aluminum, ink, hot stamping and offset printing process specifications, and the meticulous operation and close cooperation of employees to ensure stable and controlled quality.
Iron first and then print the unique secret, come and see!
Mar 25, 2026
Leave a message
Send Inquiry

