Industry knowledge

Detailed maintenance of the anilox roller

Nov 17, 2026 Leave a message

Specific key points for maintaining textured rollers-how many are you doing right?

 

Daily Maintenance (After Each Shift / After Each Ink Change)

1. Immediate Cleaning. After production ends or ink is changed, you must clean the anilox roller immediately to prevent ink from drying in the cells. Especially when the roller is hot, the ink dries faster and is harder to clean.

2. Cleaning Method. Ultrasonic cleaning is preferred: use a professional ultrasonic cleaner (frequency 40kHz, temperature ≤50℃) (as shown in Figure 1) with a special eco-friendly cleaning solution. Its cavitation effect can thoroughly clean the bottom of the cells without causing damage. Detailed steps are as follows:

 

info-1-1

Figure 1 Ultrasonic cleaner cleaning the screen roller

(1) Mix the cleaning solution and water at a 3:1 ratio (different brands of cleaning solution have different concentrations, so the ratio may vary). The solution level should contact the roller by about 5mm. Wear rubber gloves while cleaning, and use a nano sponge to scrub the roller surface. First, wipe off the ink on the roller surface, then soak the roller in the solution to further soften any ink residues in the mesh holes. You can also use ultrasonic cleaning for a deeper clean. The rule for ultrasonic cleaning is: no matter how long the soaking time is, the ultrasonic generator should be run for no more than 3 minutes. For screen rollers with over 1000 lpi, it's recommended to keep it under 2 minutes. Prolonged ultrasonic cleaning may cause serious damage to the screen roller. If the cleaning effect isn't ideal, check the cleaning solution first.

(2) After cleaning with the solution, rinse the roller thoroughly with clean water to remove any leftover cleaning solution (as shown in Figure 2).

 

info-1-1

Figure 2 Wipe with clean water

(3) After rinsing with clean water, use a highly absorbent cotton cloth to wipe off the water on the roller surface. The roller's color will return to the factory gray-white (as shown in Figure 3).

 

info-600-1

Figure 3 Comparison of roller surface moisture before and after wiping

If you don't have ultrasonic equipment, you can use manual cleaning methods. Here's how: use a nano sponge dipped in a special cleaning solution and gently wipe along the circumference of the anilox roller. After cleaning, rinse with clean water. Be sure not to use metal brushes or blades.

3. Short-term protection. If the machine is going to be stopped for a short time, you can keep the anilox roller in an inked state or loosen the doctor blade so that the roller surface stays coated and moist with ink. Also, cover it to avoid light exposure (especially for anilox rollers used with printing varnish or glue).

Deep maintenance (periodically / when ink transfer is poor)

After using the anilox roller for a while or noticing poor ink transfer, it needs deep cleaning and professional inspection.

1. Deep cleaning. For anilox rollers with dried ink or surface staining, use a strong deep cleaning solution for a long soak to soften the dried ink, then combine ultrasonic cleaning and nano sponge for restorative cleaning. Here's how:

(1) First, clean the ink off the roller surface. Then evenly apply a "strong deep cleaning solution" or "water-pattern cleaning solution" to the roller surface and wrap the roller with plastic wrap (as shown in Figure 4). This helps the cleaning solution better soften and break down the ink in the cells and prevents the solution from evaporating too quickly, improving the cleaning effect.

 

info-1-1

Figure 4 Wrap the roller with plastic wrap

(2) After soaking the roller for 3–4 hours, remove the plastic wrap and repeatedly wipe it with a nano sponge. You'll clearly see the residual ink on the roller surface being broken down. Then clean the roller thoroughly (as shown in Figure 5). Note that since the degree of mesh clogging varies, the above steps can be repeated until the mesh returns to normal.

 

info-1-1

Figure 5 Cleaned Anilox Roller

2. Professional Inspection. Regularly (recommended every quarter) check the wear and blockage of the anilox roller cells using a high-powered microscope, measure the cell volume, and create a performance record for the anilox roller.

Storage Maintenance

1. Cleaning and Rust Prevention. After thoroughly cleaning and drying the anilox roller, apply a layer of special protective oil to both sides of the roller.

2. Environmental Control. The storage area for anilox rollers should be kept at 15–30°C with humidity maintained at 40%–60%.

3. Safety Protection. Always cover anilox rollers to prevent dust and light exposure during storage, avoiding high temperatures that speed up material aging or low temperatures that cause brittleness. Excessive humidity can cause the roller core to rust, while too low humidity may lead to material cracking. Additionally, the storage area should be kept away from corrosive chemicals like acids, alkalis, and organic solvents.

In summary, the author has explained some important points and precautions to consider during the use and maintenance of anilox rollers. Overall, as an indispensable component in flexographic printing, proper and organized management of anilox rollers can lead to significant cost savings for label printing companies, allowing the value of the rollers to be maximized.

 

Send Inquiry