Industry knowledge

Gravure printing VOCs waste gas purification treatment combined process

Jan 10, 2019 Leave a message

Gravure printing VOCs waste gas purification treatment combined process

We are a big printing company in Shenzhen China . We offer all book publications, hardcover book printing, papercover book printing, hardcover notebook, sprial book printing, saddle stiching book printing, booklet printing,packaging box, calendars, all kinds of PVC, product brochures, notes, Children's book, stickers, all kinds of special paper color printing products, game cardand so on.

For more information please visit 

http://www.joyful-printing.com.   ENG only    

http://www.joyful-printing.net 

http://www.joyful-printing.org

email: info@joyful-printing.net


At present, the biggest drawback of gravure printing is that it contains volatile VOCs with large air volume and low concentration. Its treatment technology does not rely solely on activated carbon adsorption, but requires combined catalytic combustion technology, steam desorption and regeneration, and purification. Comprehensive management techniques such as processing. In this paper, through the analysis of the process flow of printing waste gas treatment, the research on the operation effect shows that the above treatment technology can purify and treat the VOCs waste gas of gravure printing to a large extent, and improve the energy saving and environmental protection effect.


In the case of gravure printing, a large amount of organic exhaust gas is usually generated, which is mainly caused by the evaporation of the organic solvent exhaust gas and the exhaust gas emitted around the printing unit when the ink is dried. Limited by the explosive limit concentration value, it will increase the exhaust gas emissions of the drying oven. In addition, it will volatilize a variety of pollutants with low concentrations: such as ethyl acetate, acetone, benzene-free ink, and ethanol produced during operation.


1 system process

Adsorbents are the decisive factor in the use of adsorption process for waste gas treatment. The adsorbent used for purifying and treating large amounts of organic waste gas is honeycomb-like activated carbon. This adsorbed carbon is superior to ordinary activated carbon in adsorption performance and has the characteristics of small airflow resistance. At the same gas flow rate, the airflow resistance of the honeycomb activated carbon is about 10% less than that of the same type of particulate carbon.


The process of gravure printing activated carbon technology mainly uses the first pre-filter to filter, and after the surface is cooled, it is introduced into the adsorption device for adsorption. After the adsorption reaches saturation, the activated carbon is desorbed using steam. The specific operation process is shown in Figure 1.


1.1 system material cycle characteristics

The entire process of gravure printing VOCs exhaust gas purification treatment is controlled by an editable logic controller, which can realize functions such as recycling, alternating adsorption, and automatic switching. The characteristics of the system material cycle are mainly the following aspects:


(1) To achieve the collection of printing exhaust gas, it is necessary to adjust the high-pressure fan to a micro-negative pressure so that it can enter the filtering process. After the exhaust gas temperature adjusting device enables the exhaust gas to smoothly enter the desorption device, the exhaust gas can be treated into a clean gas by the adsorption tank, so that recycling can be realized.


(2) The activated carbon can generate a mixed gas by using a steam desorbing device after adsorbing the printed exhaust gas, and after a plurality of heat exchanges, a condensed liquid is formed, and then the condensed liquid is rectified, and the organic product can be purified for production.


(3) To oxidize the organic matter in the exhaust gas into harmless water and carbon dioxide, it is necessary to catalytically burn the gravure-printed exhaust gas by catalytic combustion technology, which can effectively ensure the safety and quality of the purification treatment of the equipment.


1.2 Pretreatment of washing and filtration process

Since gravure printing produces organic waste gas with particle paint mist during operation, it is necessary to thoroughly remove the particulate paint mist contained in the organic waste gas before entering the adsorption tank. Intermittent high pressure showering is used to treat molecular diffusion and the like. This allows the macromolecules contained in the exhaust gas to enter the adsorption tank for adsorption treatment.


1.3 Activated carbon adsorption purification process

Usually, the adsorption device is composed of three adsorption tanks, which are capable of circulating desorption adsorption, regeneration and gas drying of the exhaust gas. The so-called gas drying actually refers to the use of activated carbon fiber to cool the gas, which can effectively remove the residual steam in the gas, and achieve the optimal adsorption effect of the adsorption tank. The exhaust gas generated during the printing process is introduced into the adsorber by the centrifugal fan. This will enable the purified gas to reach the discharge standard.


2 device parameter configuration

In the evolutionary adsorption of printed organic waste gas, honeycomb-like activated carbon is generally used for adsorption, but it is necessary to pay attention to optimizing the catalytic combustion device and activated carbon adsorption to achieve the best adsorption state. In the desorption and drying stages, the optimal configuration of the two devices enables timed automatic rotation, which ensures that the desorption operation operates simultaneously with solvent recovery.


2.1 operating parameters and system design

Toluene is the most concentrated substance in the printing exhaust gas, so there are strict requirements on its emission standards. Therefore, the primary task of exhaust gas treatment is to reduce the concentration of toluene. The adsorption recovery of activated carbon fiber is mainly to control the temperature and thickness of the bed, as well as the gas flow rate. The higher bed temperature will affect the evolution of recycling. In general, the exhaust content of gravure VOCs is generally controlled at about 80%.


2.2 adsorption bed structure

Under normal circumstances, the assembly structure of the adsorption bed is a drawer type, which is because the drawer type has a baffle arrangement to prevent gas short circuit, which can ensure uniform gas flow rate. Honeycomb activated carbon with independent adsorption unit in the drawer can improve the efficiency of material replacement and loading and unloading. In order to reduce energy consumption and reduce noise pollution when using the adsorption bed, it is recommended to use medium and low pressure exhaust fans.


The pebbles with a thickness of about 30 cm are laid under the activated carbon of the adsorption tank. The purpose of this is to avoid excessive combustion of the activated carbon, which leads to the explosion of the organic waste gas. Secondly, the activated carbon with different characteristics can be effectively stacked inside the adsorption tank. The multiple adsorption of activated carbon.


2.3 Catalytic combustion device

The main links of the catalytic combustion device are: preheating link, heat exchange link and combustion link. Usually, the honeycomb rare earth catalyst is placed in a combustion chamber, preheated by electric heating, and the organic matter in the exhaust gas is decomposed and adsorbed by the function of desorption and regeneration, and the remaining part will pass through. Catalytic combustion is converted to water and carbon dioxide. Since the catalytic bed releases a large amount of heat during operation, it will help the organic gas to spontaneously ignite, so there is no need to heat it.


Exhaust gas purification and combustion through the catalytic bed can eliminate secondary pollution, improve purification efficiency, and achieve energy saving and emission reduction.


2.4 safety aids

When performing exhaust gas purification treatment, an explosion-proof type fan should be used for the transportation of the exhaust gas. This is due to frequent switching of the equipment during gas operation. Therefore, the design of the pipe diameter and the sealing ring design of the equipment should be increased during the design, which can improve the quality and safety of the equipment. The adsorption tank is specially treated and placed into a unique drainage structure to prevent the adsorption tank from corroding the adsorption tank due to long-term liquid accumulation. The external control system of the safety barrier is used to make the whole system fully contact the ground and improve the safety performance of the equipment.


3 process scope

The combined process of activated carbon adsorption and catalytic combustion purification treatment is not suitable for exhaust gas containing large molecular weight, and the material in the exhaust gas has volatile energy, high boiling organic matter, and a substance which can react with activated carbon. And the concentration of VOCs waste gas should be controlled at about 0.5%. If this standard is not met, it should be diluted in the early stage.


4 Conclusion

The combined process of gravure printing VOCs waste gas treatment mainly combines the adsorption of activated carbon with the catalytic combustion device, which can improve the adsorption treatment effect of VOCs waste gas, avoid secondary pollution, and purify and recycle the waste gas of gravure printing VOCs. Upgrade to a new height. By using an activated carbon adsorption device equipped with three adsorption tanks, the exhaust gas can be recycled, and the adsorption performance can be maximized to achieve high adsorption efficiency.


In addition, activated carbon fiber can achieve the operating specifications of low-pressure exhaust fans with its low regenerative energy consumption, powerful desorption function and winding core process with low airflow resistance. When the catalytic bed is subjected to catalytic combustion, a large amount of heat is generated, which can help the part of the organic matter in the waste to achieve self-ignition conditions, so that it can be desorbed and regenerated, thereby achieving the effect of energy saving and emission reduction. The realization of the process of purification and treatment of gravure-printed VOCs is in line with the requirements of the era of energy conservation and environmental protection, and is conducive to the development of an environment-friendly and resource-saving society.

Send Inquiry