Offset printing machine can not increase the speed of fault repair
We are a big printing company in Shenzhen China . We offer all book publications, hardcover book printing, papercover book printing, hardcover notebook, sprial book printing, saddle stiching book printing, booklet printing,packaging box, calendars, all kinds of PVC, product brochures, notes, Children's book, stickers, all kinds of special paper color printing products, game cardand so on.
For more information please visit
http://www.joyful-printing.com. ENG only
http://www.joyful-printing.net
http://www.joyful-printing.org
email: info@joyful-printing.net
The JLS205 (or 206) type offset press sometimes fails to increase the maximum speed during operation. In its numerous reasons (1. Circuit phase loss or undervoltage operation; 2. Increased corresponding normally open contact closure of the increase and decrease relays; 3. Control circuit voltage output is insufficient...), six of the top number of main circuits The output current of the thyristor is inconsistent (the difference between large and small) is the most difficult to repair. This is because: to repair such a fault, it is usually necessary to use a dual-trace oscilloscope to re-adjust the trigger angle of the six flip-flops to restore the same - the output current values of the six thyristors in the main circuit are also restored. You can only troubleshoot the problem. The use of dual-trace oscilloscopes for adjustment, more operating procedures, more time-consuming, especially at night or when production tasks are very tight, it is not very suitable, and then encountered oscilloscope at this time (or in use) problems, then It is even more annoying or has nothing to do. In order to solve this problem, I have developed a clamp current meter to measure the thyristor AC line current value instead of using a dual trace oscilloscope to measure the trigger angle of each trigger (actually by measuring the current of each thyristor indirectly) The method of triggering the angle of each trigger is simple and practical, and can basically achieve the purpose of quickly troubleshooting (and there is no possibility that the clamp current meter may have problems in use). The details are as follows (this method requires two people to cooperate with the maintenance):
After opening the front and rear doors of the power distribution cabinet, start the low speed operation and then increase the speed to the medium speed. One person in the back door of the power distribution cabinet, holding a clamp-type ammeter, respectively, to measure the AC incoming current value of the six thyristors in the main circuit (the installation positions of the six thyristors on the front door side of the power distribution cabinet are shown in Figure 1. ), and make a corresponding record, and then tell the person standing on the front door side to adjust the trigger angle of the six triggers to facilitate adjustment (the person standing on the front door side should put the "slope" on the six triggers in advance) The lock nut of the potentiometer is loosened so that it can be adjusted with an electric pen. The installation position of the six triggers on the front door side of the power distribution cabinet is shown in Figure 2. According to the measured current, the minimum and maximum adjustments should generally be selected. Because the current of a thyristor in the three-phase full-controlled rectifier circuit changes (due to the adjustment), the current of the entire circuit will have a chain reaction - the operating current affecting the other or several other thyristors also occurs. Change, and the greater the current change of the tuned person, the greater the influence on the current of the other or other thyristors, so it should be fine-tuned to adjust the "slope" potentiometer, but not too large; otherwise It is possible to make the circuit more and more chaotic. For example, if the output current of No. 1 thyristor (SCR1) is 2A with a clamp ammeter, the output current of SCR6 is 18A, and the output current of other thyristors is measured. Around 9A, the current reference value of the whole circuit should be about 9A; 9A can be used as the reference value, and the "slope" potentiometer of the No. 1 flip-flop can be fine-tuned to gradually increase the output value - the output of the No. 1 thyristor The current is gradually increased from 2A (for example, it is now increased to 6-7A). Is the output current of the No. 6 thyristor reduced by 18A (for example, has dropped to 13~14A)? If there is any change, it means that the adjustment is effective, then continue to fine-tune the No. 1 trigger, so that the output current of the No. 1 thyristor continues to rise, and the output current of the No. 6 thyristor follows, until it reaches the ideal value of 9A. Come over, fine-tune the "slope" potentiometer of the 6th trigger to make the output value of the 6th trigger smaller - the output current of the 6th thyristor drops, and force the output current of the 1th thyristor to rise until Achieve the desired value of 9A); or alternately adjust two (1st and 6th) triggers (this is to adjust a flip-flop to change the current of the thyristor, but not to cause another thyristor current to occur The same proportion of the reverse change, or both sides can not reach the normal value after the change, but there are some differences, in this case, it is necessary to adopt the alternating and matching adjustment method to achieve the effect), so that the output current of the respective controlled thyristor Gradually become consistent. Then measure the working current of several other thyristors - see if there is any influence of regulation and increase or decrease the current? If yes, adjust it separately according to the situation... When the operating currents of the six thyristors are adjusted to be consistent (normal value), the speed will be increased synchronously; then press “speed up” To make the speed of the machine as high as possible - see if it can reach the highest speed? If the maximum speed can be reached, it means that the adjustment is successful once; if the maximum speed is not reached, the clamp current meter can be used to measure the AC inlet current values of the six thyristors at high speed, and the difference is greater. They are finely adjusted until the output currents of the six thyristors are aligned - the machine speed can rise to the highest speed. Then press deceleration to make the machine speed down to low speed and then shut down. In order to detect whether the fault has been completely eliminated, you can try again after restarting (including jog, low speed, increase and deceleration). After correct, re-tighten the lock nut of the “slope” potentiometer on each trigger.

